Page 1 of 34 12311 ... LastLast
Threads 1 to 20 of 676

Forum: Amanda 2.6.x Installation, Configuration and Administration

Amanda 2.6.x questions, issues and success stories

  1. Sticky Thread Sticky: Amanda 2.6.1p1 released

    Started by paddy, April 10th, 2009 05:10 PM
    • Replies: 7
    • Views: 15,530
    June 14th, 2010, 09:52 PM Go to last post
  2. Sticky Thread Sticky: Release of amanda-2.6.0

    Started by martineau, April 1st, 2008 11:07 AM
    • Replies: 2
    • Views: 14,023
    August 27th, 2008, 11:21 AM Go to last post
  1. Hi, centos 6 user here, working on backups!

    Started by sheilaanderson, April 11th, 2018 01:51 AM
    • Replies: 0
    • Views: 639
    April 11th, 2018, 01:51 AM Go to last post
  2. amcheck error with client same as host

    Started by lactroi, June 6th, 2017 05:03 AM
    • Replies: 0
    • Views: 5,567
    June 6th, 2017, 05:03 AM Go to last post
  3. Holding disk needed?

    Started by tuanhuylink, June 2nd, 2017 07:14 AM
    • Replies: 0
    • Views: 882
    June 2nd, 2017, 07:14 AM Go to last post
  4. slot issues

    Started by vladguan, April 20th, 2017 08:15 PM
    • Replies: 1
    • Views: 1,673
    April 20th, 2017, 08:36 PM Go to last post
  5. incrementing to the same tape

    Started by napata, May 30th, 2016 03:33 PM
    incremental, single tape drive, tape strategy
    • Replies: 0
    • Views: 7,710
    May 30th, 2016, 03:33 PM Go to last post
  6. Disaster Recovery Question

    Started by munkitkat, April 5th, 2016 02:39 AM
    • Replies: 0
    • Views: 3,818
    April 5th, 2016, 02:39 AM Go to last post
  7. backup restore changes permission

    Started by munkitkat, March 26th, 2016 05:23 AM
    • Replies: 0
    • Views: 3,413
    March 26th, 2016, 05:23 AM Go to last post
  8. Can't open tape device error - amcheck

    Started by markt, February 11th, 2016 09:22 AM
    • Replies: 2
    • Views: 4,372
    March 23rd, 2016, 05:03 AM Go to last post
  9. Backing up to a tape drive connected to a client

    Started by duongkhue84, January 19th, 2016 01:50 AM
    • Replies: 2
    • Views: 3,981
    January 19th, 2016, 06:03 AM Go to last post
  10. Long run time and insane compression ratio

    Started by DaleRobinson, December 9th, 2015 03:01 AM
    • Replies: 0
    • Views: 4,336
    December 9th, 2015, 03:01 AM Go to last post
  11. Changing gnutar_list_dir

    Started by jscarville, November 20th, 2015 06:48 AM
    amanda-client, conf, gnutar_list_dir, read only
    • Replies: 3
    • Views: 4,353
    November 21st, 2015, 06:41 AM Go to last post
  12. Exclamation bash: ammt: command not found

    Started by solarik, August 24th, 2015 01:24 PM
    ammt, no file, no program
    • Replies: 2
    • Views: 4,985
    August 25th, 2015, 04:41 AM Go to last post
  13. Clients must have user "amandabackup"?

    Started by Yzord, March 17th, 2015 05:49 AM
    • Replies: 3
    • Views: 5,406
    July 6th, 2015, 05:31 AM Go to last post
  14. The dumps did not finish properly!

    Started by Yzord, April 1st, 2015 05:41 AM
    • Replies: 2
    • Views: 4,562
    May 11th, 2015, 04:19 AM Go to last post
  15. Post Amanda Overwrite on the Tape

    Started by kamkis, April 6th, 2015 12:50 AM
    • Replies: 0
    • Views: 4,115
    April 6th, 2015, 12:50 AM Go to last post
  16. Clear VTapes

    Started by vladguan, September 28th, 2014 10:19 PM
    • Replies: 3
    • Views: 4,986
    March 26th, 2015, 05:35 AM Go to last post
  17. Problem about backups to vtape

    Started by macbookpro, January 29th, 2015 04:56 AM
    • Replies: 1
    • Views: 4,279
    March 18th, 2015, 04:30 AM Go to last post
  18. Information about Restore

    Started by macbookpro, January 29th, 2015 04:59 AM
    • Replies: 2
    • Views: 4,573
    March 4th, 2015, 01:49 AM Go to last post
  19. Question about ZMC & AMANDA

    Started by davidhan, September 25th, 2014 06:45 PM
    • Replies: 1
    • Views: 4,238
    February 28th, 2015, 12:37 AM Go to last post
    • Replies: 1
    • Views: 4,477
    February 20th, 2015, 03:11 AM Go to last post

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •