Page 1 of 34 12311 ... LastLast
Threads 1 to 20 of 673

Forum: Amanda 2.6.x Installation, Configuration and Administration

Amanda 2.6.x questions, issues and success stories

  1. Sticky Thread Sticky: Amanda 2.6.1p1 released

    Started by paddy, April 10th, 2009 05:10 PM
    • Replies: 7
    • Views: 13,870
    June 14th, 2010, 09:52 PM Go to last post
  2. Sticky Thread Sticky: Release of amanda-2.6.0

    Started by martineau, April 1st, 2008 11:07 AM
    • Replies: 2
    • Views: 12,973
    August 27th, 2008, 11:21 AM Go to last post
  1. slot issues

    Started by vladguan, April 20th, 2017 08:15 PM
    • Replies: 1
    • Views: 611
    April 20th, 2017, 08:36 PM Go to last post
  2. incrementing to the same tape

    Started by napata, May 30th, 2016 03:33 PM
    incremental, single tape drive, tape strategy
    • Replies: 0
    • Views: 6,704
    May 30th, 2016, 03:33 PM Go to last post
  3. Disaster Recovery Question

    Started by munkitkat, April 5th, 2016 02:39 AM
    • Replies: 0
    • Views: 2,973
    April 5th, 2016, 02:39 AM Go to last post
  4. backup restore changes permission

    Started by munkitkat, March 26th, 2016 05:23 AM
    • Replies: 0
    • Views: 2,619
    March 26th, 2016, 05:23 AM Go to last post
  5. Can't open tape device error - amcheck

    Started by markt, February 11th, 2016 09:22 AM
    • Replies: 2
    • Views: 3,194
    March 23rd, 2016, 05:03 AM Go to last post
  6. Backing up to a tape drive connected to a client

    Started by duongkhue84, January 19th, 2016 01:50 AM
    • Replies: 2
    • Views: 2,940
    January 19th, 2016, 06:03 AM Go to last post
  7. Long run time and insane compression ratio

    Started by DaleRobinson, December 9th, 2015 03:01 AM
    • Replies: 0
    • Views: 3,548
    December 9th, 2015, 03:01 AM Go to last post
  8. Changing gnutar_list_dir

    Started by jscarville, November 20th, 2015 06:48 AM
    amanda-client, conf, gnutar_list_dir, read only
    • Replies: 3
    • Views: 3,254
    November 21st, 2015, 06:41 AM Go to last post
  9. Exclamation bash: ammt: command not found

    Started by solarik, August 24th, 2015 01:24 PM
    ammt, no file, no program
    • Replies: 2
    • Views: 3,907
    August 25th, 2015, 04:41 AM Go to last post
  10. Clients must have user "amandabackup"?

    Started by Yzord, March 17th, 2015 05:49 AM
    • Replies: 3
    • Views: 4,111
    July 6th, 2015, 05:31 AM Go to last post
  11. The dumps did not finish properly!

    Started by Yzord, April 1st, 2015 05:41 AM
    • Replies: 2
    • Views: 3,523
    May 11th, 2015, 04:19 AM Go to last post
  12. Post Amanda Overwrite on the Tape

    Started by kamkis, April 6th, 2015 12:50 AM
    • Replies: 0
    • Views: 3,326
    April 6th, 2015, 12:50 AM Go to last post
  13. Clear VTapes

    Started by vladguan, September 28th, 2014 10:19 PM
    • Replies: 3
    • Views: 3,831
    March 26th, 2015, 05:35 AM Go to last post
  14. Problem about backups to vtape

    Started by macbookpro, January 29th, 2015 04:56 AM
    • Replies: 1
    • Views: 3,369
    March 18th, 2015, 04:30 AM Go to last post
  15. Information about Restore

    Started by macbookpro, January 29th, 2015 04:59 AM
    • Replies: 2
    • Views: 3,502
    March 4th, 2015, 01:49 AM Go to last post
  16. Question about ZMC & AMANDA

    Started by davidhan, September 25th, 2014 06:45 PM
    • Replies: 1
    • Views: 3,319
    February 28th, 2015, 12:37 AM Go to last post
    • Replies: 1
    • Views: 3,527
    February 20th, 2015, 03:11 AM Go to last post
    • Replies: 1
    • Views: 3,759
    February 15th, 2015, 08:25 PM Go to last post
    • Replies: 3
    • Views: 9,982
    February 11th, 2015, 01:10 AM Go to last post
  17. Information About Amanda 2.6.0

    Started by davidhan, September 25th, 2014 06:53 PM
    • Replies: 2
    • Views: 4,225
    January 5th, 2015, 03:31 AM Go to last post

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •